TE Connectivity UK Ltd

Address:
Merrion Ave,
Stanmore,
Middlesex
HA7 4RS
United Kingdom

Phone: 01793528171

Fax: +44-208-954-6234

Web: www.te.com


TE Connectivity UK Ltd articles

Displaying 1 - 20 of 403

Sockets support four or eight multi-processor system architectures

Sockets support four or eight multi-processor system architectures
TE Connectivity (TE) has introduced its LGA 4189 socket and hardware products, which support Intel next-generation central processing units (CPUs) for higher performance and better system scaling. LGA 4189 sockets are designed for Intel’s next-generation processors, which support PCIe Gen 4 and four or eight multi-processor system architectures. 
30th August 2019

Snap-cap electrical connectors enhance heavy equipment reliability

Snap-cap electrical connectors enhance heavy equipment reliability
High vibration, extreme temperatures, moisture, dust, dirt and debris exposure can wreak havoc on electrical harnesses and heavy machinery in harsh agricultural, mining, and construction conditions. TE Connectivity (TE), is hoping to solve this problem with its next generation 2-pin and 3-pin connector series innovation: the rear latching snap-cap DEUTSCH DT connector with wire seal covers. 
29th August 2019

Rugged, high-capacity, sealed interconnects install easily

Rugged, high-capacity, sealed interconnects install easily
TE Connectivity has introduced its single-pole DEUTSCH DTSK power connectors designed for rugged, sealed applications. These heavy-duty thermoplastic connectors accept size Ø8mm contacts that are rated up to 125 amps. TE’s DEUTSCH DTSK connectors are designed to withstand the harsh conditions of the trucking, busing, agricultural, mining, construction and marine industries, as well as other industrial applications.
1st August 2019


High performance, versatile solution for higher current applications

High performance, versatile solution for higher current applications
TE Connectivity (TE) has introduced an extension of its VAL-U-LOK connector product line that increases the maximum current rating from nine to 13A in the broadly accepted 4.2mm centerline spacing connector system. TE’s new 13A VAL-U-LOK connectors support high current requirements for wire-to-board and wire-to-wire connections in a wide range of applications where power must be connected to a board or subsystem. 
3rd July 2019

TE Connectivity completes acquisition of Kissling Group

TE Connectivity completes acquisition of Kissling Group
Connectivity and sensors solutions provider, TE Connectivity (TE), completed the previously announced acquisition of the Kissling group of companies (Kissling or Kissling Group) on May 24th.
7th June 2019

Right angle X-Code M12 connectors reduce assembly time

Right angle X-Code M12 connectors reduce assembly time
Specialist in connectivity and sensors, TE Connectivity (TE), has begun offering extremely ruggedised X-Code M12 right angle connectors for field assembly in a range of railway applications. The new connectors enable safe and reliable data transmission speeds of 10Gb/s, even in harsh environments. 
6th June 2019

Innovative test solution for digital switchgear announced

Innovative test solution for digital switchgear announced
TE Connectivity offers an innovative test solution for digital switchgear, including sensors. The ESSAILEC RJ45, part of the ESSAILEC test blocks range, is designed to fit electricity utilities’ requirements for safe and reliable testing. Test operations can be made without opening the switchgear panel door and without changing the wiring.
5th June 2019

New high-voltage automotive connector

New high-voltage automotive connector
TE Connectivity (TE) has launched its new Generation Y connectors for high-voltage (HV) automotive battery applications. The product extends TE’s range of Generation Y connectors that can be used in HEV batteries. The Generation Y HV connectors support a signal current range from 4-10.5A and a voltage rating of up to 432V.
28th May 2019

High voltage connector designed for EV battery applications

High voltage connector designed for EV battery applications
  TE Connectivity has introduced its AMP+ HVA 1200 HV Terminal and Connector System. The product is a significant addition to TE’s range of high voltage connectors for hybrid and all-electric vehicles. With the new AMP+ HVA1200 HV terminal and connector system (HVA 1200) automotive manufacturers benefit from a high performance interconnection system for their next-gen vehicles.
28th May 2019

Enabling photovoltaic system installers to make fast connections

Enabling photovoltaic system installers to make fast connections
Connectivity and sensor solutions provider, TE Connectivity (TE), has introduced SOLARLOK 2.0 connectors. The new products enable photovoltaic system installers to make reliable connections more easily, quickly and cost-effectively. SOLARLOK 2.0 is a field-installable product that uses Insulation Displacement Contact (IDC) technology to create a connection between panels and cables without the need for any specialist tooling. 
16th May 2019

IHVA high-voltage DC contactor for superior control

IHVA high-voltage DC contactor for superior control
Specialist in connectivity and sensors, TE Connectivity (TE), has introduced the IHVA 200, a DC contactor for 200A/110VDC loads, with improved cost-effectiveness and reliability to high-voltage battery charging stations. The contactor incorporates a patented design that does away with the standard charging station approach of using inert gases in a hermetically sealed zone to prevent explosions when an excess current or voltage is applied. 
14th May 2019

New high voltage automotive connector launched

New high voltage automotive connector launched
  TE Connectivity has launched its new Generation Y connectors for High Voltage (HV) automotive battery applications. The product extends TE’s range of Generation Y connectors that can be used in HEV batteries. The Generation Y HV connectors support a signal current range from 4 to 10.5A and a voltage rating of up to 432V.
8th May 2019

High-performance lightweight high-current relay

High-performance lightweight high-current relay
Connectivity and sensors solutions provider, TE Connectivity (TE), has introduced its new Battery Disconnect Relay 12V (BDR 12V) for automotive high-current applications. The product extends TE's range of high-current (HC) relays that can be used in automotive and industrial applications.
3rd May 2019

Digital combination sensor designed for accurate monitoring

TE Connectivity’s (TE) TRICAN 5V is designed for engine and fuel cell applications that require a low power, digital combination sensor for accurate monitoring and diagnosis in harsh vehicle environments.
1st May 2019

Deal expands hybrid electric commercial vehicle portfolio.

Deal expands hybrid electric commercial vehicle portfolio.
A definitive agreement has been signed by TE Connectivity (TE) to acquire the Kissling group of companies, a provider of high- power relays and ruggedised switches used in a range of industries as well as other applications. The transaction is expected to close May 30th, 2019, following the completion of customary regulatory approvals.
29th April 2019

Single pair Ethernet as common solution for future of IIoT

Single pair Ethernet as common solution for future of IIoT
Specialist in connectivity and sensors, TE Connectivity (TE), is cooperating with fellow connector producer HARTING to set Single Pair Ethernet (SPE) as the de facto infrastructure to enable the Industrial Internet of Things (IIoT). The two companies will together drive solutions that define the infrastructure for SPE. 
8th April 2019

Stainless-steel D-sub connectors for nontoxic applications

Stainless-steel D-sub connectors for nontoxic applications
Specialist in connectivity and sensors, TE Connectivity (TE), recently released its new line of rugged AMPLIMITE D-subminiature (D-sub) connectors that put the same corrosion resistance of connectors made with cadmium into an environmentally-friendly, stainless-steel housing.
28th March 2019

Enabling luminaires without limitations

Enabling luminaires without limitations
Specialist in connectivity and sensors, TE Connectivity (TE), has introduced a new compact connectivity solution for street lighting with LED light sources. TE´s LUMAWISE Endurance S module consists of a standardised interface (Zhaga Book 18) between the receptacle and module base or sealing cap. 
26th March 2019

Poke-in connectors for a wide range of LED lighting applications

Poke-in connectors for a wide range of LED lighting applications
  TE Connectivity has unveiled BUCHANAN WireMate ITB (Inverted Thru-Board). These wire-to-board connectors are for use in linear and circular LED modules found in all sorts of commercial and industrial lighting systems.
25th March 2019

Rugged backplane connector with vibration resistance

Rugged backplane connector with vibration resistance
Specialist in connectivity and sensors, TE Connectivity (TE), has launched its fastest rugged backplane connector, the MULTIGIG RT 3 connector. TE’s MULTIGIG RT 3 connectors support speeds of 25+Gb/s, reportedly making them among the fastest rugged backplane connectors for embedded computing or VPX systems currently on the market.
13th March 2019


Sign up to view our publications

Sign up

Sign up to view our downloads

Sign up

EMO Hannover 2019
16th September 2019
Germany Hannover
European Microwave Week 2019
29th September 2019
France Porte De Versailles Paris
HETT 2019
1st October 2019
United Kingdom EXCEL, London
World Summit AI 2019
9th October 2019
Netherlands Taets Park, Amsterdam
New Scientist Live 2019
10th October 2019
United Kingdom ExCeL, London