Like Goldilocks, op amps need things to be just right

3rd November 2016
Posted By : Joe Bush
Like Goldilocks, op amps need things to be just right

 

Daniel Burton of Analog Devices (ADI) offers some advice when selecting an op amp for a precision signal path, and asks, is faster always better?

Choosing the appropriate bandwidth for an application of a precision op amp is a lot like the experience of Goldilocks trying to choose between the three bears’ bowls of porridge - one bowl was too hot, one bowl was too cold, and one was just right. We would like an amplifier that is not too slow and not too fast, but gives our signal all the gain and speed necessary to maintain stability and accuracy.

The key op amp specifications for a voltage feedback op amp in this application are the gain bandwidth product (GBP) and the phase margin (PM). Figure 1 (below) shows the open loop gain and phase vs. frequency for the ADA4610, a popular precision op amp. The plot shows that the op amp gain at low frequency is greater than 30,000 (90dB), rolling off at 20dB per decade, and reaching unity (0dB) at about 10MHz - known as the unity gain crossover frequency. The op amp open loop gain plot gives the ability to determine its GBP and design an amplifier circuit with a given closed loop gain and bandwidth such that GBP = gain × BW, as shown in Figure 2 (below). For example, notice how a one decade decrease in closed loop gain (AV) from 100 (or 40dB) to 10 (or 20dB) results in a one decade increase in bandwidth, from 163kHz to 1.63MHz.

Similarly, the op amp phase plot in Figure 1 relates to the inherent phase shift of a signal as it passes through the op amp. The phase margin can be approximated by reading the phase shift at the bandwidth of the amplifier circuit. In the case of the ADA4610, it is approximately 67°, which is plenty of phase margin for stability. If the system design causes the phase margin of the amplifier circuit to decrease to the point that it is too small, it can manifest with symptoms like significant ringing at the output or even oscillation. In addition to stability, accuracy is affected by frequency. At low frequencies, the open loop op amp gain (AVOL) is highest and is sometimes referred to as the DC gain. As the frequency increases, the gain decreases and gain error gets worse. Thus it doesn’t take much frequency until we start seeing gain error that may be too great for a precision sensor signal.

The amount of closed loop gain can be calculated using the following equation. Where β is the feedback factor, 1/β is the ideal closed loop gain (for example, 100V/V in the green line in Figure 2 - below), and the product Aβ is called the loop gain.

As the loop gain decreases with frequency, there is an increase in gain error. The percentage of error can be calculated by the following equation:

Graphically, the loop gain Aβ can be thought of as the difference between the open loop DC gain in Figure 1 (and also listed in the datasheet specifications) and the closed loop gain in Figure 2. For example, using a nice round number of 100dB for the op amp open loop gain, and an ideal closed loop gain of 40dB, we get a loop gain of 60dB (or 1,000V/V).

So, if more bandwidth and loop gain is better, why not use an op amp with a GBP much higher than that of our signal gain and bandwidth? There are a number of reasons not to use excessive GBP. The broadband noise of an op amp integrates over the bandwidth of an amplifier. If we choose an op amp bandwidth greater than necessary, there will be excessive noise that will be gained up by the amplifier circuit and reduce the system’s signal-to-noise ratio.

Higher speed op amps are more susceptible to system parasitic capacitance, which can add lag to the feedback signal and reduce the phase margin and therefore the stability. Finally, faster op amps consume more power because the idling current on the op amp output stage must be higher in order to drive load capacitances at a higher frequency. Choosing the fastest op amp can impact power and signal quality. Picking too slow of an op amp can leave your accuracy, stability and other performance measurements in the cold. Finding the op amp with the right balance of speed, gain, accuracy, and phase margin for your application will be just right.


You must be logged in to comment

Write a comment

No comments




Sign up to view our publications

Sign up

Sign up to view our downloads

Sign up

EMO Hannover 2019
16th September 2019
Germany Hannover
European Microwave Week 2019
29th September 2019
France Porte De Versailles Paris
HETT 2019
1st October 2019
United Kingdom EXCEL, London
World Summit AI 2019
9th October 2019
Netherlands Taets Park, Amsterdam
New Scientist Live 2019
10th October 2019
United Kingdom ExCeL, London